最近中文字幕2019视频1,少妇久久久久久被弄到高潮,欧美黑人粗暴多交高潮水最多,50岁老熟女高潮喷了

產品展示
首頁 > 產品展示 > > 其他檢測儀器 > TC-500 氧氮聯合測定儀

TC-500 氧氮聯合測定儀

簡要描述：簡單說明：TC500系列儀器質量、性能、工藝滿足您對金屬、難熔物、其他無機材料日常生產中氮/氧分析的需要

  • 產品型號：TC-500
  • 廠商性質：生產廠家
  • 更新時間：2024-10-08
  • 訪  問  量：1633
詳情介紹

詳細說明:

TC500系列儀器質量、性能、工藝滿足您對金屬、難熔物、其他無機材料日常生產中氮/氧分析的需要

Determination of Oxygen and Nitrogen in
Reactive/Refractory Metals and Their Alloys*
 
Approval
ASTM E-1409 Oxygen Determination in Titanium and Titanium Alloys
ASTM E-1569 Oxygen Determination in Tantalum
ASTM E-1937 Nitrogen Determination in Titanium and Titanium Alloys
 
Sample Preparation
A clean representative sample is required in order to obtain optimum results. Solid samples can be leached in suitable acid or abraded with a clean file, rinsed in acetone, and dried with warm air. Refer to ASTM methods above for further details.
 
Accessories
782-720 Crucible; 782-721 Electrode Tip; 502-344 UHP Nickel
Baskets; 501-073 Graphite; 503-032 Glass Accelerator Scoop;
501-059 Tin Capsules—for powdered samples. （Additional steps required for powdered samples are noted in parenthesis.）
 
Calibration Standard
LECO 501-320 Titanium Pin, 502-047 Zirconium Pin, NIST, or other suitable reactive/refractory metal standard.
 
Method Parameters
Analysis Parameters
Outgas Cycles                           2
Analysis Delay （seconds）             20
Analysis Comparator                 1
Analysis Type                              Auto
 
Element Parameters                  Oxygen           Nitrogen
Minimum Time （seconds）
35
55
Integration Delay （seconds）
5
15
Comparator Level （%）
1
1
 
Furnace Parameters
Furnace Control Mode             Power
Purge Time （seconds）                    15
Outgas Time （seconds）                20
Cool Time （seconds）                    5
Outgas Power （Watts）                 6300
Analyze Power （Watts）                5300
 
 
 
 
 


 

*This includes Ti, Zr, W, Mo, Ta, Nb, Hf, and their alloys.

 
TC500


 

 
Typical Results
 
 
 
Titanium Pin
Mass （g）
Oxygen （%）
Nitrogen （%）
 
0.1135
0.1808
0.0189
 
0.1133
0.1843
0.0194
 
0.1134
0.1831
0.0184
 
0.1138
0.1819
0.0188
 
0.1133
0.1821
0.0195
 
0.1131
0.1829
0.0185
 
0.1134
0.1833
0.0191
 
0.1143
0.1849
0.0194
 
0.1125
0.1837
0.0189
 
0.1072
0.1830
0.0191
 
Average
0.1830
0.0190
 
Std. Dev.
0.0012
0.0004
 
Zirconium Wire
 
Mass （g）
 
Oxygen （%）
 
Nitrogen （%）
 
0.1067
0.1246
0.0017
 
0.0978
0.1273
0.0017
 
0.1180
0.1246
0.0019
 
0.1097
0.1235
0.0014
 
0.1141
0.1272
0.0017
 
0.1017
0.1226
0.0018
 
0.1140
0.1269
0.0020
 
0.0987
0.1239
0.0020
 
0.1015
0.1233
0.0022
 
0.1197
0.1270
0.0020
 
Average
0.1251
0.0018
 
Std. Dev.
0.0018
0.0002
 
Procedure
 
 
 
1.   Determine the blank as follows:
a.   Enter the "blank" ID code with a 1.0000 g weight in the weight stack.
b.   Press the loader control switch, the sample loader will open.
c.   Place one 502-344 UHP Nickel basket into the loading head using clean tweezers.
（Place a 501-059 Tin capsule into the Nickel basket before placing it in the loading head.）
d.   Press the loader control switch, the sample loader will close and seal and the furnace electrode will open.
e.   Remove crucible from electrode tip and discard.  Clean furnace area using the appropriate brushes.  Vacuum away loose dust.
f.    Place ~0.05 g 501-073 into the bottom of a 782-720 crucible.  ~0.05 g is approximay a ¼ full
503-032 glass accelerator scoop.
g.   Place the crucible on the lower electrode.
h.   Press the loader control switch, the furnace electrode will close and the analysis sequence will start automatically.
i.    Repeat steps 1a through 1h at least four more times.
j.    Enter blank following routine outlined in operator's instruction manual.
2.   Calibrate the instrument as follows:
a.   Weigh the calibration sample. （Weigh the calibration sample into the tin capsule.）
b.   Enter the calibration sample ID code and sample weight in the weight stack.
c.   Place the calibration sample （capsule） into a nickel basket.
d.   Press the loader control switch, the sample loader will open.
e.   Carefully place the calibration sample/nickel basket （capsule） into the loading head using clean tweezers.  Make sure that the calibration sample （capsule） stays in the basket and the basket
stays upright.
f.    Press the loader control switch, the sample loader will close and seal and the furnace electrode will open.
continued on page 3


 

Procedure （continued from page 2）
g.   Remove crucible from electrode tip and discard.  Clean furnace area using the appropriate brushes.  Vacuum away loose dust.
h.   Place ~0.05 g graphite into the bottom of a crucible.
i.    Place the crucible on the lower electrode.
j.    Press the loader control switch, the furnace electrode will close and the analysis sequence will start automatically.
k.   Repeat steps 2a through 2j a minimum of three times.
l.    Complete a calibration by following the auto calibration procedure as outlined in the operator's instruction manual.
m.  Verify the calibration by analyzing the calibration sample again.  It should fall within the expected tolerances.  If not, repeat steps 2a through 2l again.
3.   Analyze the samples as follows:
a.   Weigh ~0.1 g sample. （Weigh the sample into the tin capsule.）
b.   Enter the sample ID code and sample weight in the weight stack.
c.   Place the sample （capsule） into a nickel basket.
d.   Press the loader control switch, the sample loader will open.
e.   Carefully place the sample/nickel basket （capsule） into the loading head using clean tweezers.
Make sure that the sample （capsule） stays in the basket and the basket stays upright.
f.    Press the loader control switch, the sample loader will close and seal and the furnace electrode will open.
g.   Remove crucible from electrode tip and discard.  Clean furnace area using the appropriate brushes.  Vacuum away loose dust.
h.   Place ~0.05 g graphite into the bottom of a crucible.
i.    Place the crucible on the lower electrode.
j.    Press the loader control switch, the furnace electrode will close and the analysis sequence will start automatically.
 
Theory of Operation
The TC500 is a microprocessor-based, software-controlled instrument that measures both nitrogen and oxygen in a wide variety of metals, refractories, and inorganic materials. The inert gas fusion principle is employed. A weighed sample, placed in a high-purity graphite crucible, is fused under a flowing helium gas stream at temperatures sufficient to release oxygen, nitrogen, and hydrogen. The oxygen in the
sample, combines with the carbon from the crucible to form carbon monoxide. The nitrogen present in
the sample releases as molecular nitrogen, and any hydrogen present is released as hydrogen gas. The helium carries the sample gases through heated rare earth copper oxide which converts carbon
monoxide to carbon dioxide （CO2） and hydrogen to water （H2O）. The nitrogen passes through
unchanged. The gases are then passed through a CO2  infrared （IR） cell where the oxygen is measured as
CO2. CO2  and H2O are then removed by a Lecosorb/Anhydrone trap, while the nitrogen passes through
to a thermal conductivity （TC） cell for determination.


 

TC500 Flow Diagram
 
 
 
 
 

留言框

  • 產品：

  • 您的單位：

  • 您的姓名：

  • 聯系電話：

  • 常用郵箱：

  • 省份：

  • 詳細地址：

  • 補充說明：

  • 驗證碼：

    請輸入計算結果（填寫阿拉伯?dāng)?shù)字），如：三加四=7

技術支持：化工儀器網   sitemap.xml   管理登陸
©2024 版權所有：寧波市鄞州瑾瑞儀器設備有限公司   備案號：浙ICP備14028217號-3

浙公網安備33020402000311號
亚洲AV无码一区东京热久久| 99精品久久精品一区二区| 久久伊人蜜桃AV一区二区| 香蕉久久人人爽人人爽人人片AV| 久久久久99精品成人片试看 | 业余 自由 性别 成熟偷窥| 少妇粗话肉麻对白视频6| 麻豆乱码国产一区二区三区| 国产乱自产黄A片在线观看| 国产日韩精品中文字无码| 免费无码高潮流白浆视频| 久久午夜夜伦鲁鲁片免费无码影视 | 一边做饭一边躁狂怎么办| 中文字幕精品亚洲无线码二区| 欧美精品久久96人妻无码| 啊灬啊灬啊灬啊灬高潮了| 扒开美女内裤狂揉下部| 精品亚洲欧美无人区乱码| 老熟妇高潮一区二区三区| 国产女人高潮嗷嗷嗷叫| 青苹果乐园全网影视大全| 亚洲国产精品无码久久久秋霞1| 穿这么少不就是给人C的| 波多野结衣52部合集在线观看| 丰满女人又爽又紧又丰满| 偷窥 性别 瘾 XXXXX| 日本边添边摸边做边爱60分钟 | 成熟丰满熟妇AV无码区| 人善交ZZZZXXXXX另类| 偷看18美女洗澡过程| 又粗又长又大真舒服好爽| 无码少妇精品一区二区免费动态 | 搡老熟女国产| 啊灬啊别停灬用力啊爷小说| 亚洲熟女乱综合一区二区| 国产精品无码麻豆放荡AV| 天天爽夜夜爽人人爽,qc| 久久精品国产亚洲AV无码偷窥| 少妇XXXXX性开放| 男人手伸进我内衣揉我胸到爽| 国产乱国产乱老熟300部|